When a furnace stops working in the middle of a cold stretch, that is the call we get most often from Attleboro. Homes here run on a range of heating equipment: forced-air furnaces, hot-water boilers, and older oil-fired systems that have been in place for decades. When any of them fails, the repair path depends on what the equipment is actually doing, not on what it looks like from the outside. We handle the full scope of residential and commercial heating and cooling work in Attleboro, from a single-room mini-split to a full system replacement on a property that has been running the same equipment since the previous owner.
Attleboro is a city of working homes and smaller commercial properties, and the HVAC calls that come out of a place this size tend to reflect that. A building manager keeping a commercial space comfortable has different needs from a homeowner whose boiler is losing pressure, but both calls start the same way. We cover AC repair, heating and furnace repair, heat pump service and installation, ductwork, thermostats, indoor air quality, and emergency calls.
Call (401) 535-9789 to get a quote, and we will walk you through what the visit covers.
The visit starts with the system, not with a recommendation. The technician who comes out looks at what the equipment is doing before anything else: whether it is running without producing conditioned air, cycling off before the house reaches temperature, making a noise it was not making last season, or not responding to the thermostat at all. That observation shapes everything that follows.
From there, the diagnostic works through the components most likely to produce that symptom. For a heating system, that means the heat exchanger, ignition, burner, and blower. For a cooling system, it means refrigerant charge, coil condition, airflow, and the controls. The findings are explained in plain terms before any repair is quoted, and the repair is quoted before any work begins. Nothing gets added to the scope without your sign-off. Clear notes on what was found and what was done come with every visit, so there is a record of the diagnosis and the repair, not just an invoice.
An air conditioner that is running but not cooling, or one that is producing ice on the indoor coil, is often carrying a refrigerant charge problem. A low charge does not fix itself. The system runs longer, the compressor works harder, and the cooling output drops. Finding where the charge went is the first step, because adding refrigerant without sealing the leak is a temporary fix at best. We locate the leak, repair it, and restore the charge to the correct level for that equipment.
Standing water near the air handler or the indoor unit of a mini-split usually means the condensate drain is blocked or the drain pan has failed. Left alone, it causes water damage and can shut the system down on a safety switch. The fix involves clearing the drain line, checking the pan, and making sure the drainage path is clear before the system goes back into service.
A coil that has accumulated enough dust and debris restricts airflow through the air handler and reduces the system's ability to transfer heat. The result is weak cooling, longer run times, and in some cases a frozen coil that stops the system entirely. Cleaning restores the airflow and the heat transfer. If the coil has developed a leak or physical damage, repair or replacement is the next step, and that gets explained before any decision is made.
Many homes in this part of Massachusetts were built before central ductwork was standard, and adding a forced-air system to one of them is often more disruptive and expensive than the alternative. A ductless mini-split delivers heating and cooling directly to the room or zone where it is needed, with no ductwork required. Installation involves mounting the indoor air handler, running the refrigerant line set and control wiring through the exterior wall, and commissioning the outdoor unit. Multi-zone systems can condition several areas independently, which makes them a practical answer for additions, finished basements, and older homes where a central system does not reach every room well. We also service and repair existing mini-split systems when refrigerant issues, drainage faults, or communication errors between the indoor and outdoor units bring them down. The full breakdown is on our heating and cooling services page.
Replacing an HVAC system is not simply a matter of matching the unit that was there before. An undersized system runs constantly and never quite reaches the set temperature. An oversized one short-cycles, which means it turns on and off too frequently to properly dehumidify the air or heat the space evenly. Both situations leave the property uncomfortable and wear the equipment faster than a correctly sized system would.
The right size depends on the square footage of the conditioned space, the insulation in the walls and attic, the number and orientation of windows, and the way the building holds or loses heat. The age of the system changes the answer, and that gets said. A property that added an extension since the original equipment was installed, or that has had insulation work done since then, may need a different capacity than what is currently in place. We work through that before recommending equipment, not after.
The cost of an HVAC repair or installation depends on what the diagnostic turns up. What the fault turns out to be, which components have to be reached to fix it, and whether a repair or a replacement is the more practical path are the factors that move the number. We do not quote a price before the system has been assessed, because a quote made without looking at the equipment is a guess.
What you get before anything is scheduled is the price for the diagnostic visit itself. What you get before any repair begins is the full quote for that repair. Neither is authorized until you have agreed to it. If the findings point toward replacement rather than repair, that conversation happens with the diagnostic in front of both parties, not as a default recommendation. Permits are handled where the job needs them, and that is confirmed as part of the scoping process.
Call (401) 535-9789 to get the process started.
Ask what the service call covers and you will get a straight answer.
A system that goes down completely in the middle of a heating or cooling season cannot wait for a standard appointment slot. We take emergency HVAC calls every day from 8:30 AM to 11:00 PM, including weekends. No-heat calls, no-cool calls, and full system-down situations are all handled within those hours. The job is scoped on the call so the visit is prepared before anyone heads out.
For properties with tenants or commercial spaces that need to stay open, the scheduling conversation happens on the call. We work around what the property needs where the schedule allows. We do not promise a specific arrival window, but emergency calls are answered and the visit is set up to be useful before it starts. We're ready to get your heating and cooling running again.
For non-emergency work, seasonal tune-ups and planned replacements are easiest to schedule a week or two ahead of when you need them. Calling before the peak of summer or the first cold snap of fall is the most reliable way to get the timing you want.
We serve Attleboro and the communities around it throughout Bristol County. That includes North Attleborough, North Seekonk, and the neighboring Rhode Island communities of Pawtucket, Central Falls, and Valley Falls. If you are between those towns or just outside the list, call and ask. We will tell you directly whether your address is covered.
Coverage means the work is done here. There is no additional charge built into the quote for being outside the city limits, and the process is the same regardless of which community the property is in.
It is worth checking that the system switch at the air handler is in the on position and that the circuit breaker has not tripped before calling. A tripped breaker that resets and holds may simply have been a momentary event. If the breaker trips again after resetting, leave it off and call us, because a breaker that keeps tripping points to a fault in the equipment or the circuit feeding it.
In a zoned system, a zone that is not conditioning usually points to a failed zone damper, a zone controller fault, or a thermostat that is not sending a signal. In a non-zoned system, one area of the house that is not being conditioned often points to a duct problem, a blocked or closed register, or a room that is simply not being reached by the distribution system. The diagnostic starts by confirming which of those is the case.
A ductless mini-split is the most practical path for a home without existing ductwork. The indoor air handler mounts on the wall or ceiling, and the refrigerant line set runs through a small opening in the exterior wall to the outdoor unit, so there is no need to open walls or ceilings to run ducts. Multi-zone systems can handle several rooms independently from a single outdoor unit. We scope the installation on the call and confirm the equipment and the price before scheduling.
A repair that does not hold is usually the result of one of three things: the wrong component was replaced, the root cause of the fault was not identified and the new part failed for the same reason, or the repair was correct but a second failing component was not caught during the same visit. We approach a system that has had recent work done by someone else with that in mind and look for both the immediate fault and the underlying cause.
Yes. A thermostat that is reading temperature inaccurately, failing to hold a setpoint, or not communicating with the air handler can make a well-functioning system behave poorly. Replacing it with a correctly configured programmable or smart control often restores normal operation without touching the equipment. Compatibility with the existing system is confirmed before anything is ordered or installed.
Call (401) 535-9789 and give us the address.
That is the fastest and most reliable way to confirm coverage. We do not rely on online maps for coverage decisions, and we will give you a straight answer on the call.
A boiler heats the living space by circulating hot water through radiators or radiant floor panels, so the diagnostic covers system pressure, the circulator pump, zone valves, the heat exchanger, and any air trapped in the distribution loop. A furnace moves heated air through ductwork, so the diagnostic focuses on the heat exchanger, burner, ignition system, and blower. The symptoms can look similar from the homeowner's side, but the components involved are different, and the repair path follows from what the equipment is actually doing rather than from the category it falls into.
We are available every day from 8:30 AM to 11:00 PM. Whether the system has stopped entirely, is running but not producing results, or is due for a seasonal check before the weather turns, the call is where it starts. Describe what the equipment is doing, or not doing, and we will scope the visit and confirm the price before anything is scheduled. One call. One clear diagnosis. One price, agreed first.
Call (401) 535-9789.
Close by, we also take heating and cooling work in: Pawtucket, Central Falls, Cumberland, Lincoln.
See our coverage area.
Whether the call is about a furnace that stopped firing, an AC that is running but not cooling, or a full system replacement, we handle the complete range of heating and cooling work for homes and commercial properties across Attleboro and Bristol County. The table below lays out what each service covers, who it fits best, and what is useful to know before you call. If you have a question that is not answered here, call us and we get into the specifics with you directly.
| HVAC Service | What It Covers | When You Need It | Good to Know |
|---|---|---|---|
| AC Repair & Service | Refrigerant charge check, Coil inspection and cleaning, Blower and airflow diagnosis, Capacitor and control testing | Homeowners and property managers with an AC that is running but not keeping up | Catching a refrigerant or airflow problem early in the season avoids a full breakdown during the hottest stretch of a Rhode Island summer. |
| Full System Installation & Replacement | Equipment sizing and selection, Removal of existing system, Full installation and commissioning, Permits handled where the job needs them | Homeowners and property managers whose existing equipment has reached end of life or requires a repair that no longer makes financial sense | Installation scope and pricing are confirmed before work starts. The quote covers the equipment and the job, and the diagnosis is what drives the recommendation, not a default position. |
| Heat Pump Repair & Service | Refrigerant circuit diagnosis, Reversing valve check, Control board testing, Efficiency and output verification | Properties with an existing heat pump that is not reaching temperature in heating or cooling mode | A heat pump that heats in summer and cools in winter has a reversing valve that can fail in one direction only, which is a common diagnostic finding. |
Call (401) 535-9789 to talk through your heating or cooling situation and get a price before anything is scheduled.
(401) 535-9789